Schoenenberger_Systeme_GmbH/dxfmakros
7
0
Fork 0
Code Issues 1 Pull Requests Actions Packages Projects Releases Wiki Activity

Merge branch 'master' of https://gitea.schoenenberger.de/Schoenenberger_Systeme_GmbH/dxfmakros

Browse Source
This commit is contained in:
Simon Hensch
2026-09-16 09:54:16 +02:00
parent 5193f4018c d9eb41f4d1
commit 3fdfb020a6
5 changed files with 690 additions and 167 deletions
Download Patch File Download Diff File Expand all files Collapse all files
lang/en_GB.json
+7
View File
@@ -46,6 +46,7 @@
"vfl-alert-winkel-ungueltig": "Incline angle invalid: %1 degrees. Allowed: 0 < angle <= %2 degrees.",
"vfl-prompt-hoehe-linienendpunkt": "\nHeight (Z) of the line end point [%1]: ",
"vfl-prompt-hoehe-linienendpunkt-2": "\nHeight (Z) of the line end point (down: %1 | up: %2) [%1]: ",
"vfl-prompt-hoehe-linienendpunkt-3": "\nHeight (Z) of the line end point (down: %1 | up: %2 | picked: %3) [%3]: ",
"vfl-hinweis-hoehe-vorschlag-fehlt": "\n(Note: no buildable suggestion found for that direction at this segment length - please check the value manually.)",
"vfl-alert-gf-kann-nicht-steigen": "Gravity section (GF) cannot rise - please pick a lower target height or use down/up VF.",
"vfl-alert-gefaelle-zu-steil": "Slope too steep for GF: %1 degrees (max allowed %2 degrees).\nPlease pick a smaller height difference or use down/up VF.",
@@ -390,6 +391,10 @@
"vfl-stufe2-minh": "\n [Fixed value without GF bend] Remainder as a straight VF section (height-neutral): this split ALWAYS results in exactly %1 mm of height change, regardless of length - but the target height calls for %2 mm, so this only fits on an exact match",
"vfl-stufe2-minh-unmoeglich": "\n [Fixed value without GF bend] Not solvable via target height: even without a straight VF section and without a GF bend, the fixed footprint is already %1 mm - the distance only offers %2 mm",
"vfl-stufe2-ungueltig": "\n Stage 2 (horizontal+GF) was invalid - stage 1 (VF angle search) was tried instead (see table above).",
"vfl-stufe3-start": "\n\n[Diagnosis stage 3 - angle + horizontal filler] Stage 1 and stage 2 failed, trying a combination of a steep S-bend and a horizontal remainder piece ...",
"vfl-frage-stufe3-position": "\n\nThe section needs an S-bend COMBINED with a straight horizontal piece. Where should the horizontal piece go?",
"vfl-opt-stufe3-vor": "\n 1 - Horizontal piece BEFORE the S-bend",
"vfl-opt-stufe3-nach": "\n 2 - Horizontal piece AFTER the S-bend",
"vfl-frage-gf2-minimum": "\n Calculated GF2=%1 mm is below the usual minimum length (%2 mm).\n Yes = build with the exact calculated %1 mm (hits the target point exactly).\n No = pad up to %2 mm (target point shifts further accordingly).",
"vfl-fuege-block-ein": "\n Inserting %1 ...",
"vfl-hinweis-gf2-minimum": "\n NOTE: calculated GF2=%1 mm < minimum %2 mm -> raised to minimum (ES therefore ends a bit further on; see actual-vs-target report).",
@@ -398,8 +403,10 @@
"vfl-kettenende-modus-ziel": "\n>>> Chain-end mode: target dL=%1 mm, dH=%2 mm (%3). GF2 varies with the angle.",
"vfl-prompt-hoehe-endpunkt": "\nHeight (Z) of the end point [%1]: ",
"vfl-prompt-hoehe-endpunkt-2": "\nHeight (Z) of the end point (down: %1 | up: %2) [%1]: ",
"vfl-prompt-hoehe-endpunkt-3": "\nHeight (Z) of the end point (down: %1 | up: %2 | picked: %3) [%3]: ",
"vfl-prompt-hoehe-kettenende": "\nHeight (Z) of the chain end (ES element) [%1]: ",
"vfl-prompt-hoehe-kettenende-2": "\nHeight (Z) of the chain end (ES element) (down: %1 | up: %2) [%1]: ",
"vfl-prompt-hoehe-kettenende-3": "\nHeight (Z) of the chain end (ES element) (down: %1 | up: %2 | picked: %3) [%3]: ",
"vfl-prompt-wahl-bis-n": "\nYour choice (1-%1) [1]: ",
"vfl-frage-auf-ab-richtung": "\n\nChain arrives flat - no target height available. Choose direction:",
"vfl-opt-richtung-auf": "\n 1 - Up",